SOVIET ARTILLERY


Ali Jalali |
Dastagir Wardak
Kimberly Franklin
John Sloan

Table of Contents


I. Role, Composition, Missions, and Principles of Artillery's Combat Employment in Front Offensive Operations
1 Composition
1 Organization of Artillery Large Units and Units
2 Missions of Artillery in Front Offensive Operations
3 Main Principles of Employment of Artillery

II. Organization of Combat Employment of Artillery in Front Offensive Operations
4 Determining Requirements for Artillery
5 Distribution of Artillery and Establishment of Artillery Groupings
6 Principle Missions of the Army Artillery Group (AAG)
6 Division Artillery Group (DAG)
7 Regiment Artillery Group (RAG)

III. Planning Actions of Rocket and Artillery Troops in Front Offensive Operations
7 Graphic Part of the Plan
7 Organization of Combat Supporting Measures of the Artillery
8 Combat-Readiness

9 IV. Combat Employment of Artillery During the Penetration of Enemy Prepared Defenses
9 Assault Support Fire
10 Accompanying Fire

11 V. Combat Employment of Artillery During the Commitment of the Front's Second-Echelon into Combat
11 Assault Support Fire
11 Accompanying Fire
11 Operational Norms for the Density of the Artillery
12 Average Norms of the Employment of Artillery to Destroy Typical Targets

15 VI. Characteristics of Artillery's Combat Employment in Front Defensive Operations
15 Missions and Principles of Combat Employment of Artillery in Defensive Operations
15 Distribution and Grouping of Artillery
16 Principles of Artillery Employment
16 Organization of Combat Employment of Artillery in Defensive Operations
16 Counterpreparatory Fire in Front Defensive Operations
16 Aims of Counterpreparatory Fire
17 Missions of Artillery During Counterpreparatory Fire
17 Planning of Counterpreparatory Fire
17 Troops Participating in Counterpreparatory Fire
17 Combat Employment of Artillery During Struggles Against Enemy Tanks During the Defense
17 Employment of Antitank Reserves
18 Missions of Front Antitank Reserves
18 Combat Employment of Artillery in Front Counterblows During Defensive Operations
19 Planning Counterblows
19 Artillery Forces and Means Assigned to Support Counterblows
19 Artillery Missions During Preparatory Fire
19 Supporting Fire
20 Accompanying Fire

20 VII. Combat Employment of Rocket Troops in Front Offensive Operations
20 Role, Composition, Missions, and Principles of Combat Employment of Rocket Troops in Front Offensive Operations
20 Missions of Rocket Troops
21 Main Principles of Employment of Rocket Troops
21 Forms of the Conduct of Missions
21 Composition of Front Rocket Troops
21 Tactical and Technical Characteristics of Rockets
22 Combat Capabilities of Rocket Troops
22 Capabilities to Inflict Losses on Various Targets
23 Organization of Combat Employment of Rocket Troops in Front Offensive Operations
25 Planning Front Initial Nuclear Strike
25 Organization of Front Initial Nuclear Strikes During the Conduct of the Offensive Operation
26 Employment of Front Rocket Troops to Repel Enemy Counterblows
26 Organization of Combat Supporting Measures of the Front Rocket Troops
27 Combat-Readiness of Rocket Troops
27 Technical Preparation of Rockets
28 Time for Bringing Rocket Troops to Full Combat-Readiness


COMBAT EMPLOYMENT OF ARTILLERY IN

FRONT OFFENSIVE OPERATIONS



I. Role, Composition, Missions, and Principles of Artillery's Combat Employment in Front Offensive Operations

Contemporary artillery troops have the following capabilities:

enormous firepower;
longer range;
accuracy of fire;
wide maneuverability;
capability to launch massive, concentrated fires quickly to great depths;
capability to destroy various targets with a high rate of fire resulting in a high density of fire;
quick initiation (opening) of fire on targets;
high maneuverability provides for concentration of the bulk of the artillery on decisive directions quickly and discretely.

The role and significance of artillery will change according to characteristics of combat actions and conditions of the employment of nuclear rocket weapons systems. In a nuclear war the artillery, within its range and capabilities, supplements nuclear strikes in the following areas:

where nuclear weapons are not planned to be used;
where limited use of nuclear weapons is planned;
areas in the immediate vicinity of the line of contact with the enemy.

Therefore, even in nuclear war artillery is one of the direct support means of the attacking troops.
Under conditions when nuclear weapons are not used, the significance of artillery is greatly increased. In this case artillery constitutes the principle means of firepower of the ground forces.

Composition

The composition of the front's artillery is determined by the following:

composition of the artillery organically subordinate to the front;
artillery organic to the front's formations and large units;
availability the Supreme High Command artillery elements to be attached to the front.

The quantity of Supreme High Command artillery attached to the front is determined by the general staff during peacetime on the basis of the following:

missions to be assigned to the front during the operation;
composition and characteristics of likely actions of opposing enemy groupings;
nature of employment of various means of destruction.

The front must be reinforced by artillery to insure the successful actions of the troops during the attack without using nuclear weapons. This is the case in which artillery is charged with the principle missions while the forces are penetrating the enemy' forward defense line or other fortified defensive lines in his operational depth, i.e., the period during which artillery is required to accomplish a large number of tasks to inflict losses on enemy targets within its effective range.

A contemporary front with a composition of three to four combined armies, one to two tank armies, and five to seven reserve divisions reinforced by three artillery divisions and two antitank artillery brigades may be equipped in the following manner:

5,000 guns, mortars, self-propelled guns, and reactive (multiple rocket) launchers;
700 antitank guns;
about 2,000 antitank guided missile weapon systems.

Organization of Artillery Large Units and Units

The organization of artillery large units and units is as follows:

High Command Artillery Divisions: A total of 246 guns and mortars are included in the divisions.

Antitank Artillery Brigade of the Reserve of the Supreme High Command: Includes four battalions each composed of four batteries, three equipped with 100 mm guns and one equipped with antitank guided missiles (nine in the battery). Total weapons in the brigade are as follows:

100 mm guns - 72;
ATGM - 36.

Army's Artillery Brigade: Includes four artillery battalions with two battalions composed of 130 mm guns (thirty-six guns in two battalions) and two battalions of 152 mm howitzers (thirty-six howitzers in two battalions). The total number of artillery pieces in the brigade is seventy-two.

Army's Antitank Artillery Regiment: Includes three battalions, each with two batteries of 100 mm guns (twelve guns) and one battery of antitank guided missiles (nine in a battery). The number of weapons in the regiment totals sixty-three as follows:

100 mm guns - 36;
ATGM - 27.


Artillery of Motorized Rifle Division:

division's artillery regiment;
two battalions of 122 mm howitzers each with eighteen howitzers, a total of thirty-six howitzers in two battalions;
one battalion of 152 mm howitzers with eighteen howitzers a total of fifty-four in the regiment.
division's separate multiple rocket launcher artillery battalion which is composed of three batteries, each battery having six BM-21 multiple rocket launchers, with a total of eighteen in the battalion.

Division's Antitank Separate Battalion: Includes three batteries each composed of six 100 mm guns, a total of eighteen guns in the battalion.

Motorized Rifle Regiment's Artillery:
one battalion of 122 mm howitzers of eighteen howitzers;
one antitank guided missile battery of nine ATGMs.

Motorized Rifle Battalion's Artillery: Includes one battery of six 120 mm mortars and one antitank platoon, consisting of four ATGM weapons and two RPG-9 grenade launchers.

[Note: The composition of artillery as discussed above and the number of artillery pieces in artillery units and large units reflects the notes taken in the Academy Voroshilov in 1975. More recently the composition and organization of artillery units and large units has expanded with the numbers of their organic guns and mortars increased. For example the current artillery division of the Supreme High Command reserve is said to be composed of more than 500 guns and mortars.]

Missions of Artillery in Front Offensive Operations

Artillery has the following missions in front offensive operations:

destroy and suppress enemy nuclear delivery means;
repulse enemy aggressions and destroy his groupings of forces which have penetrated friendly territory;
support deployment of first-echelon large units;
organize support of the passage of front forces through enemy covering forces;
destroy the enemy in meeting engagements;
support breakthroughs of enemy defensive lines;
support attacking forces during operations in the depth of the enemy defenses with assault supporting fire and accompanying fire;
support the front when crossing water obstacles;
participate in repulsing enemy counterblows (counterattacks);
support commitment of second-echelons of armies and the front in combat;
assist in destroying enemy encircled groupings of forces;
support consolidation of seized lines and areas;
cover gaps, open flanks, and boundaries across the front.

Main Principles of Employment of Artillery

The main principles of the employment of artillery are as follows:
massive employment of artillery on important directions of the front's attack;
close interaction with motorized rifle, tank troops, and the air force;
support attacking troops with fire in a continuous form;
firm and continuous control of fire and maneuver.

The role and importance of artillery is so great that it is called "the God of the war." Experiences from the Great Patriotic War indicate that achieving fire superiority over the enemy on important directions is considered a required condition for the success of combat actions of troops in operations without nuclear weapons. This may be achieved only through superiority in numbers of fire means, primarily artillery and the air force. Fire superiority enables the destruction and suppression of enemy weapons affecting friendly motorized and tank troops. The more this task is accomplished with success, the fewer the losses sustained by friendly troops will be. The enemy possesses an increasing number of modern artillery weapons in his composition of forces including nuclear artillery, the destruction of which is a very important task of the artillery. The enemy's artillery is mostly self-propelled and it has wide maneuverability, which enables the artillery to relocate frequently. Increased numbers of artillery pieces and shells are needed to fight such artillery. Contemporary defense makes use of large numbers of the following:

tanks;
self-propelled guns;
armored fighting vehicles (BMP type vehicles);
antitank guided missiles with high maneuverability.

Moreover, engineer work in the defense is highly developed. Using modern technical equipment, the enemy may quickly fortify his position and may effectively cover his personnel, weapons, and equipment. This further necessitates a larger number of artillery pieces and ammunition to fight the enemy. The required fire superiority must be established in the direction of the main attack so that enemy defenses are effectively penetrated and attacking troops may quickly advance into the depth of enemy defenses. Systematic supply of artillery ammunition in accordance with the progress of the attack is one of the requirements of the offensive operation.

II. Organization of Combat Employment of Artillery in Front Offensive Operations


The organization of the combat employment of the artillery in front offensive operations is the sum of a number of measures conducted by the front's chief of artillery and rocket troops and his staff which include the following:

make decisions on employing artillery and rocket troops;
plan combat employment of artillery and rocket troops;
group, distribute, and allocate artillery for accomplishing assigned missions;
assign (convey) missions to rocket troops and artillery;
organize interaction (coordination);
prepare FUP areas for the attack and positions for the artillery and rocket troops to cover the deployment of the main groupings of forces;
collect and stockpile material means;
organize political affairs of rocket and artillery troops;
organize all combat supporting measures;
organize troop control, preparation of command posts and signal systems;
prepare troops for combat action;
maintain high combat-readiness of troops for accomplishing assigned missions.


Planning the combat employment of the artillery includes the following measures:
determine the needs of first-echelon armies for attached artillery (for artillery reinforcement);
distribute the Supreme High Command's artillery to front organic formations;
orgafriendlynize movements of artillery to cover deployment of main groupings of front forces, and to repel likely enemy aggressions, and to support initiation of the attack by forces;
organize actions of the artillery during the conduct of the following front missions:
during conduct of artillery preparatory fire, assault support fire, accompanying fire, and covering boundaries, flanks, and gaps by fire;
while repulsing enemy counterblows (counterattacks);
during assault crossings over water obstacles;
while committing second-echelon troops into combat;
while conducting meeting engagements;
while conducting other important front missions.

determine the composition of front antitank reserves and specify their likely missions and the method of movement of front antitank reserves during offensive operations.
organize the front's supply formations with artillery equipment and ammunition.

Determining Requirements for Artillery

The front's requirements for artillery are determined by the needs of first-echelon armies and the number of artillery required for establishing front antitank reserves. The requirements for artillery are greater while breaking through the enemy's prepared defensive lines, particularly his forward defensive line where larger portions of enemy weapons and means are concentrated and the defensive positions are better fortified by engineer work. In such cases artillery will be required to accomplish a large number of missions to suppress simultaneously all targets within its effective range. In order to determine the army's need for artillery the number of targets in the following areas are calculated:
on enemy forward defensive lines;
in penetration areas.

These targets are to be engaged simultaneously during artillery preparatory fire. The number of targets to be hit by the air force is deducted from the sum. To destroy the remaining targets the necessary number of artillery pieces are determined on the basis of the established norms for destroying (suppressing) typical targets. From the number of required artillery, as calculated above, the army's organic artillery is deducted, the balance represents the army's additional requirement for artillery (artillery reinforcement). The sum of first-echelon armies' requirements for artillery constitutes the front's need for artillery. The second-echelon armies receive artillery reinforcement (attached artillery) when they are committed into combat. At this time they are given artillery reinforcements by diverting (resubordinating) Supreme High Command's artillery units and large units attached to first-echelon armies. Therefore, needs (requirements) of second-echelon armies for artillery do not count while assessing front requirements for artillery.

When necessary information about the targets is not available, and during peacetime planning, the number of artillery pieces required is calculated by the required concentration of artillery for a penetration sector of 20-25 km frontage. In this calculation 90-100 guns per kilometer of front (against U.S. forces) are taken as the norm.
For artillery fire in penetration areas not only the artillery of the division conducting the penetration is assigned, but also the army artillery, and under favorable conditions the artillery of the second-echelon divisions of the army is also called to participate.

The front's second-echelon army's artillery is unavailable to be called to participate in artillery preparatory fire since its return movement of 200-300 km will be difficult. (It is located with its parent army at this depth from the frontline). By the same token calling artillery of other first-echelon divisions to penetration areas is not practiced so that those divisions are not stripped of their artillery. Moreover, maneuver of the artillery parallel to the front is difficult. In some conditions only reactive (multiple rocket launcher) artillery of the divisions adjacent to penetration areas may be called since they have high maneuverability.

To support the penetration of the army in a zone composed of the adjoining penetration areas of two adjacent divisions at a seven to eight km frontage, seven-hundred to eight-hundred guns and mortars are required. If three armies operate in the front first-echelon, a total of 2,100-2,400 guns and mortars are required to support penetration at the front level.

The following organic army artillery may be called to operate in penetration areas:

artillery of two motorized divisions: 126 + 126=252;
army's artillery brigade=72;
artillery regiment and reactive (multiple rocket launchers) artillery battalion of army second-echelon divisions=72;
total=396.

Therefore, the army must be reinforced by 300-400 guns and mortars which amounts to nearly 1.5 artillery divisions (if one artillery division contains 246 guns and mortars). Thus front requirements for artillery depend on artillery needs of front first-echelon armies.
| The required number of artillery may be decreased in the following ways:
extending the duration of preparatory fire;
assigning aircraft and tanks;
reducing the penetration areas.

The front must have a sufficient number of artillery in its composition to insure successful accomplishment of the mission.

In order to establish front first-echelon armies' antitank reserves on tank threatened directions, two to three antitank brigades of the reserve of the Supreme High Command are needed. One to two of these brigades constitutes the front's antitank reserve. This front antitank reserve may cover an area of twenty to twenty-five km wide, on tank threatened directions, in cooperation with first-echelon large units and may repel the attack of one to two enemy armored divisions or reestablished exhausted antitank reserves for one to two armies.

Distribution of Artillery and Establishment of Artillery Groupings

Artillery is distributed and organized in groupings in accordance with concepts and conditions of front offensive operations.
At the front level only an antitank reserve is established. Front antitank reserves may include, in addition to one to two antitank brigades, tank and engineer subunits.
During operations on tank threatened directions, the army must be given in addition to one artillery division, two to three antitank battalions.
The tank army without organic artillery, is primarily given (attached) long-range artillery (to fight enemy nuclear delivery means and artillery). When the army has organic army artillery it is given (attached) reactive (multiple rocket launcher) artillery.
Artillery groups of armies and divisions are composed of organic and attached artillery in accordance with characteristics of actions and assigned missions. Efforts must be made toward providing self-sufficient divisions and regiments to accomplish assigned missions. The division attacking on the main direction must be given four to five artillery battalions. Other divisions are given one to three artillery battalions.
In order for the army commanders to have their own assets for exerting influence on the situation and the enemy (particularly while conducting penetration on adjoining flanks of first-echelon divisions), an army artillery group composed of eight to ten artillery battalions, including four to five long-range artillery battalions is established. The army assists its divisions by the army artillery group, particularly those divisions which attack on main directions.


Principle Missions of the Army Artillery Group (AAG)

The principle missions of the army artillery group are as follows:
destroy enemy nuclear delivery means and fighting against them;
destroy and suppress enemy artillery;
reinforce first-echelon division's fire, particularly divisions attacking on the main direction;
destroy and suppress enemy immediate reserves, particularly on directions of penetration and main attacks;
fire assistance (support) of large units operating on directions of main attacks;
disrupt enemy command and control.

When divisions operate in a wide area, the concentration of army artillery groups (AAG) in one area in one group does not seem logical. Therefore, in such cases artillery units of the army artillery group are attached to divisions operating in areas where the AAG or divisions newly committed into combat are located.
The army artillery group (AAG) may be divided into several sub-groups. The number of sub-groups is determined by the number of divisions operating in first-echelon on directions of main attacks.
The greater capability of reactive (multiple rocket launcher) artillery, and its availability as an organic component of artillery divisions of the reserve of the Supreme High Command (which are attached to the front) provide for and necessitate establishment of the army reactive artillery group (AGRA) for centralized employment in the direction of main attacks and to conduct rapid maneuver of artillery to required directions in order to carry out missions inflicting losses on main enemy groupings.

Division Artillery Group (DAG)

The division artillery group is composed of four to six artillery battalions consisting of the following:
guns;
howitzers;
reactive (multiple rocket launchers).

Division artillery group's missions are as follows:
fight enemy nuclear delivery means;
destroy and suppress enemy immediate reserves;
destroy and suppress enemy artillery;
reinforce fire of regiment's artillery groups.

Some of the artillery battalions of the division artillery group are assigned to support first-echelon regiments.

In second-echelon divisions and regiments artillery groups are established after their commitment into combat.

Regiment Artillery Group (RAG)

The regiment artillery group is composed of three to four artillery battalions. It is assigned to conduct missions directly in the interest of its related regiment, particularly to fight against enemy mortars. It may also be called, as needed, to participate in destroying the artillery.
Part of the artillery battalions of the regiment artillery group is assigned to support first-echelon battalions. During the attack and after seizing defensive positions of enemy first-echelon battalions, these artillery battalions may be attached to motorized rifle and tank battalions.

III. Planning Actions of Rocket and Artillery Troops in Front Offensive Operations

The chief of rocket and artillery troops makes plans for front rocket and artillery troops after clarifying missions and decisions from the front commander on employing rocket and artillery troops and instructions from the staff of the higher echelon on employing rocket and artillery troops. He then conducts a thorough and all-around assessment of the situation and makes decisions on combat employment of rocket and artillery troops.

The details of planning the combat employment of rocket and artillery troops are shown in the plans for combat employment of front rocket and artillery troops. The elements are a principle part of the front operational plans and the principle document of the rocket and artillery staff. The plan is prepared on a 1:500,000 or 1:200,000 scale map along with written instructions.

Graphic Part of the Plan

The graphic part of the plan illustrates the following points:
enemy situations, his important groupings, and targets of rocket troops;
situations and missions of front and armies and boundaries between armies;
missions of rocket troops in initial and subsequent nuclear strikes to include specific targets, yields of nuclear rounds, types of bursts, the rocket sub-units and units launching strikes on specific targets, and the time of launching the strike;
employment of rocket troops against enemy means of counternuclear weapons struggle;
directions of movement, position areas (deployment and assembly areas) of rocket troops, rocket technical units and large units, and artillery and their relocation during the operation;
groupings of armies' and division's artillery;
penetration areas and density of artillery there;
areas of location and directions of action of antitank reserves of armies and divisions;
areas of location and direction of actions of front antitank reserves;
maneuver of rocket and artillery troops during operations;
areas of radar coverage and positions of air defense artillery;
other elements of combat formations.

Annexes to the plan include the annex of the initial nuclear strike and the written instructions. The written instructions contain the following:
specific numbers of nuclear and chemical rockets allocated for the operation and their distribution in terms of the initial nuclear strike, front missions, and among different armies;
availability and distribution of conventional rockets in terms of front missions and among armies;
combat composition of front rocket and artillery troops, distribution of artillery of the Supreme High Command (attached to the front), and front artillery among armies and their regroupment during the operation;
distributing of artillery ammunition in terms of front missions and among armies;
composition of antitank reserves.

In addition to these, the following points are reflected in other work documents:
method, time of preparation, and delivery of rockets to troops;
calculations of the time for bringing artillery and rocket troops to a state of full combat-readiness;
expenditure of conventional rounds;
measures for protecting troops against mass-destruction weapons.

The plan for employing rocket and artillery troops is signed by the front chief of artillery and his chief of staff. It is approved by the front commander.

Organization of Combat Supporting Measures of the Artillery

Well organized combat support measures constitute one of the main factors in achieving success in accomplishing assigned missions. Combat support measures of artillery are the following:
artillery reconnaissance;
prepare artillery positions, protected places (shelters) for personnel, covered areas for vehicles and equipment, observation posts and facilities, and protected places for ammunition;
(maskirovka) conceal positions in terrain, engineer work, and weapons and combat equipment;
air defense against enemy air strikes;
protect troops against mass-destruction weapons;
supply ammunition and artillery equipment;
topogeodetic, topographic, and hydrometeorological support;
radio-electronic combat.


Combat-Readiness;

There are three levels of combat-readiness in rocket and artillery troops.

1. Constant Combat-Readiness: Units and sub-units are kept at full combat strength as much as possible. Units conduct their daily training in accordance with the plan. They are capable of conducting assigned missions. Weapons and equipment are ready for combat employment. Weapons, ammunition, and other supplies are kept up to norms.

2. Higher State of Combat-Readiness: Rocket and artillery units may be brought to the state of full combat -readiness in the shortest period of time. In this state of combat-readiness all units and sub-units are brought to full garrison accommodation, combat duty service is reinforced, and combat service is conducted in full combat-readiness. Officers and men are called to duty from leave. Material means and ammunition are loaded in vehicles. Units and sub-units are ready to move out from the garrisons. Operational groups with signal equipment are sent to command posts.

3. Full Combat-Readiness: This is assumed in accordance with the plan and by the signal of combat alert. In this state of combat-readiness units and sub-units move out of their permanent garrisons to assembly areas or to position areas and occupy fire positions. Necessary combat preparations are made by units and subunits so they are ready to conduct combat missions. Simultaneously, units and subunits are brought up to full combat strength by using mobilization reserves.

IV. Combat Employment of Artillery During the Penetration of Enemy Prepared Defenses

One of the important and difficult phases of front offensive operations is penetration (breakthrough) of enemy prepared defenses. The enemy's prepared defense is penetrated either from the move (S Khodu - line of march) or from the position of direct contact with the enemy after artillery preparatory fire. Missions of artillery during preparatory fire are the following:
destroy enemy nuclear delivery means;
inflict sufficient losses on enemy artillery, mortars, antitank weapons, and his air defense batteries;
suppress enemy personnel in their defensive strong points;
destroy enemy troop control systems.

All of these tasks are conducted by artillery preparatory fire. Artillery fire is conducted in the penetration area and for one kilometer on each flank of the penetration area across the front. This enables it to destroy enemy antitank weapons on the flanks of the penetration area as well.

The duration of preparatory fire depends on the desired degree of loss to be inflicted. On average preparatory fire lasts for thirty to forty minutes. The same amount of time is required for movement of troops from the line of deploymentttt into battalion columns during the attack from the line of march.

During conduct of artillery preparatory fire the following may be assigned to participate:
army artillery group;
artillery groups of divisions and regiments conducting the penetration;
artillery of second-echelon divisions of the army;
reactive artillery (multiple rocket launchers) of the divisions adjacent to the penetration area.

The structure of artillery preparatory fire includes 2-3 heavy fire strikes each lasting 10-15 minutes with a density of 90-120 guns and mortars per kilometer of width of the penetration area.

Assault Support Fire

Assault fire is the creation of a fire barrage behind which tanks and infantry advance during the attack and inflict losses on the following:
enemy artillery;
other enemy weapons;
enemy air defense artillery;
enemy personnel.

Assault support fire continues until the attacking units reach the depth of enemy first-echelon battalion positions (depth of three kilometers). Fire is conducted by the following methods:
successive concentration of fire (PSO);
double successive concentration of fire;
rolling fire barrage (OV);
double rolling fire barrage;
a combination of these methods.

In the double method artillery is divided into two groups. One group fires successively on the first line, while the other engages targets on the second line with successive concentration of fire. The first group shifts the fire in accordance with the call of battalion commanders or as the battalions reach the limit of safe distance of the first line of PSO fire. The first group shifts fire to the second line while the second group shifts its fire from the second to third line. The distance between these lines is 400-600-800 m.

Accompanying Fire

Accompanying fire on targets resisting against the attacking troops is conducted in the following forms:
concentration of fire (SO);
massive fire (MO).

For artillery to prepare for fire during penetrating enemy defenses six to eight hours are required. Maneuver of the artillery requires that two of these hours be daylight for coordination and confirmation of missions on the terrain.

During penetration of enemy defenses the following artillery groups need to be established:
army artillery group (AAG);
army's reactive artillery group (AGRA);
divisional artillery group (DAG);
regimental artillery groups (RAG).

Note: Now with increased artillery in Soviet units and large units assault support fire (when targets are not very mobile) may be conducted to the depth of defending brigade's positions (up to eight kilometers).


V. Combat Employment of Artillery During the Commitment of the Front's Second-Echelon into Combat

One decisive form of expansion of efforts during offensive operations is the commitment of the front second-echelon (combined arms or tank army) into combat. This should greatly change the operational situation in favor of the front's attacking troops. The second-echelon army is committed during the completion of the immediate mission or at the beginning of the subsequent mission. The second-echelon army may be committed in the following areas:
in areas of one or two armies operating in the first-echelon to further develop the attack;
at adjoining flanks of two armies;
in gaps created during the operation;
in areas weakly occupied by the enemy.

The army is committed in the following ways:
entirely at once;
in a successive method;
only part of it is committed into combat.

In any form successful commitment of the second-echelon army into combat requires the conduct of powerful artillery preparatory fire and establishment of artillery groups in the army and its divisions and regiments. The missions of artillery in this artillery preparatory fire are the following:
destroy enemy nuclear delivery means;
reliably suppress enemy antitank defenses in the area of commitment of front secondechelon forces into combat;
reliably suppress enemy artillery and mortars;
destroy enemy troop control systems;
suppress enemy personnel, weapons, and tanks located in strong points.

Artillery preparatory fire lasts up to 30 minutes and includes 2-3 heavy artillery strikes each lasting 10-15 minutes. The density of artillery in this case should be forty to sixty guns and mortars and more per kilometer of front. The expenditure of ammunition will be 0.6 - 0.8 units of fire.

Assault Support Fire

Assault support fire is conducted on two to three lines mostly by massive fire (MO) and concentration of fire (SO) on enemy defensive strong points.

Accompanying Fire

Accompanying fire is conducted by massive fire (MO) and concentration of fire. In order to support the commitment of the front second-echelons into combat, maneuver of artillery is conducted toward the area of commitment. This maneuver is conducted to establish the required density of artillery for suppression of the enemy and also to establish the artillery groups of the army, divisions, and regiments. Maneuver of artillery and preparation of fire require four to six hours.

To provide systematic fire support (preparatory fire, assault support fire, and accompanying fire) the artillery of the army's second-echelon is committed into combat, as well as, the artillery of those troops which operate in the areas of the second-echelon's commitment.

Control of the artillery in the second echelon's area of commitment is conducted by the chief of rocket and artillery troops of the front.

Rocket troops remain in their positions, ready to launch nuclear strikes when required.

Front antitank reserves, as a rule, jointly operate with front mobile obstacle detachments (POZ). The front's antitank reserve is ready for deployment at the line of front second-echelon commitment or it deploys in front of the line or on threatened flanks of the line of commitment.

Operational Norms for the Density of the Artillery

The operational norms for the density of artillery to inflict simultaneous losses on the enemy during preparatory fire (25-30% losses criteria), considering enemy nationality and width of the penetration area are shown on the following table.

NORM FOR DENSITY OF ARTILLERY

Enemy nationality Width of penetration area 4 km 6 km 8km 12km
U. S. Mechanized (Armored) Div 130 per km 120 per km 115 per km 110 per km
FRG Motorized Infantry (Tank) Div 120 per km 115 per km 110 per km 105 per km
Uk Motorized Infantry (Tank) Division 115 per km 110 per km 105 per km 100 per km
Belgium and Holland Motorized Infantry (Tank) Division 110 per km 105 per km 100 per km 95 per km

Average Norms of the Employment of Artillery to Destroy Typical Targets

The norms are shown on the following table.
(in artillery pieces firing fifteen minutes)

TARGETS UP TO 10 KM MORE THAN 10 KM

IN DISTANCE IN DISTANCE

launching pad (to 6 12 be destroyed)

launching pad (to 6 6 inflict losses on)

battery (platoon) of 12 18 guns, mortars, and self-propelled guns

battery (platoon) of 6 12 guns, mortars, and sp -guns without armor

air defense artillery 12 18 or SAM battery

radar or control and 6 12 guidance center

personnel in covered 12 18 in prepared defense
strong points of platoons (6 hectares)

personnel in covered 12 12 in hasty defense
strong points of platoons (6 hectares)

division forward 24 36 command post (8 hectares)

TARGETS UP TO 10 KM MORE THAN 10 KM

IN DISTANCE IN DISTANCE

brigade command 12 18 post (4 hectares)

battalion command 6 12 post (2 hectares)

personnel (covered) 54 54 in assembly areas same for same for
infantry (company tank tank in 400 x 400 meters) company company

personnel in assembly 18 18 area (in open and exposed infantry company)

VI. Characteristics of Artillery's Combat Employment in Front Defensive Operations

Defense by the front in contemporary times is a temporary and forced form of combat action. It is assumed only when attack is not possible due to a lack of forces and means or when the attack is not logical on the basis of operational and strategic concepts. In any case the front assumes the defense when its forces and means are not plentiful enough for attack. Therefore, it opts to inflict heavy losses on the enemy by defensive actions and changes the correlation of forces and means in favor of friendly forces. Then it initiates offensive operations for achieving assigned aims.
Here we briefly discuss some specific issues related to employment of artillery in front defensive operations.

Missions and Principles of Combat Employment of Artillery in Defensive Operations

Artillery's Missions in Defense

Artillery's missions in defense are the following:
destroy and suppress enemy nuclear delivery means;
inflict losses on main groupings of enemy forces:
by massive fires from temporary positions during enemy movement toward the defense;
by massive fires from temporary positions during enemy deployment in assembly areas;
by counterpreparatory fires, massive fires, and concentration of fire from temporary positions on the enemy forces in their attack (FUP) positions inflicting heavy losses on enemy main groupings.
repulse enemy attacks with all systems of fire such as:
rolling barrage (PZO);
fixed barrage (NZO);
massive fires (MO);
concentration fires (SO).

inflict losses on the enemy during combat in the depth of the defense, preventing penetration of the enemy to the flanks by:
fixed barrage fire (NZO);
rolling barrage fire (PZO);
massive fire and concentration fire (SO).

inflict losses on the enemy during counterpreparatory fire which is conducted by:
one heavy fire strike;
short preparatory fire.
conduct assault support fire by:
successive concentration fire (PSO) on two to three lines;
mostly by massive fire and concentration fire in support of counterblows.

conduct accompanying fire by:
massive fire (MO);
concentration fire during the conduct of counterblows.

Fight enemy artillery during combat actions to achieve fire superiority over the enemy on specific directions.

Distribution and Grouping of Artillery

During defensive actions the front will receive smaller artillery reinforcements. Therefore, the front distributes available artillery among armies and retains part of it for establishing its own antitank reserve. As in the offensive operation, the front does not establish the front artillery group. The following artillery groups will be created in defensive operations.

regiment artillery groups (RAG): Established in regiments operating on directions of enemy main attacks or defending on main defensive directions.

division artillery groups (DAG): Established in all divisions to assist regiments defending on directions of enemy main attacks and to inflict losses on enemy artillery and mortars.

army artillery groups (AAG): Established when sufficient artillery is available in the front and when enemy attacks are likely to be launched on specific directions and enemy attacks are expected to be conducted in narrower frontage.

Principles of Artillery Employment

Principles of artillery employment are the following:
massive use of artillery to foil enemy attacks and to inflict maximum enemy losses and concentration of fire power on directions of enemy main attacks and on movement routes, deployment lines, and attack positions (FUP areas) of the attacking enemy;
establish a barrage of dense fire of all types of fire means and fires of antitank weapons in front of the forward line (FLOT) on likely directions of enemy attacks and struggle against enemy tanks and nuclear weapons;
continue support of the combat action of defending troops during operations and during conduct of counterblows and counterattacks;
continue interaction with rocket troops, air force, motorized rifle, and tank forces in foiling enemy attacks.

Organization of Combat Employment of Artillery in Defensive Operations

Organization of combat employment of artillery in defensive operations is the sum of measures conducted by the chief of front artillery and rocket troops and his staff on organization of the use of artillery units and large units in defensive operations which include the following:
make decisions on employment of rocket and artillery troops;
plan combat employment of artillery and rocket troops;
assign (convey) missions to rocket troops and artillery;
organize coordination (interaction);
prepare main, alternate, and temporary positions of artillery and prepare lines of deployment (lines of fire) and positions of antitank reserves;
collect (supply) and dump material means;
organize political affairs;
organize all types of supporting measures;
organize troop control, prepare command posts, and establish signal systems;
prepare troops for action and maintain high combatreadiness of troops for accomplishing the assigned missions.

Counterpreparatory Fire in front Defensive Operations

In defensive operations, in order to foil enemy attacks or weaken or delay enemy attacks, counterpreparatory fire may be conducted by front artillery and rocket troops.

Aims of Counterpreparatory Fire

Aims of counterpreparatory fire include the following:
foil enemy attacks;
weaken striking enemy groupings;
gain time to complete defenses and to delay enemy attacks.

Missions of Artillery During Counterpreparatory Fire



Missions of artillery during counterpreparatory fire are as follows:
destroy enemy nuclear delivery means;
suppress enemy artillery, mortars, and air defense artillery;
destroy enemy command and control systems, i.e., destroy enemy command posts, command and control, and signal communication means; inflict losses on enemy groupings of forces particularly tanks.

Planning of Counterpreparatory Fire

Counterpreparatory fire is planned in the following forms:
while in direct contact with the enemy; In this case main fire strikes are launched against enemy artillery and tank troops.
while the enemy is located in depth and moving to attack defenses from the line of march, i.e., when the enemy is initially out of range of the artillery of the defending forces; In this case the artillery launches strikes against enemy command posts and his artillery while friendly aircraft and rocket troops deliver strikes on main groupings of enemy forces in depth.

Troops Participating in Counterpreparatory Fire

During counterpreparatory fire as many artillery, air force, and rocket troops as possible are employed, i.e., all available artillery of first-echelon divisions, armies' artillery, and artillery of armies' second-echelon divisions are employed.

Counterpreparatory fire is conducted from temporary positions. Considering (including) the maneuver time of artillery, four to six hours are required for preparation of artillery to conduct counterpreparatory fire.

Counterpreparatory fire is a front level measure. It is conducted in accordance with decisions of the front commander. Under some conditions counterpreparatory fire may be conducted in army areas as well. Direct preparation of counterpreparatory fire is conducted in army areas.

Duration of counterpreparatory fire includes two to three strikes lasting ten to fifteen minutes.

The depth of counterpreparatory fire is extended as far as the range of the artillery will permit. It is conducted against enemy first-echelon divisions. Aircraft launch strikes against targets in the enemy's depth.

The density of artillery during counterpreparatory fire is thirty to forty guns and mortars per kilometer of front.

Combat Employment of Artillery During Struggles Against Enemy Tanks During the Defense

One of the important issues in the defense is the struggle against enemy tanks and armored vehicles. The struggle includes the following:
coordinate artillery fire with strikes of rocket troops and the air force;
continue cooperation with tank and engineer troops;
prepare all artillery for struggle against tanks, prepare all types of fires, and deploy artillery to cover tank threatened directions so that it may engage the intruding tanks with direct (flat trajectory) fire.

In this case destruction of tanks is conducted from artillery's actual positions or through relocation of artillery to positions prepared in advance for this purpose.

Destruction of enemy tanks is conducted by the following methods:
massive fires (MO), concentration fires (SO), and barrage fires from covered positions against tanks in their assembly areas, during their movement to the defense, and during their deployment;
in front of the forward defense line and in the depth, by fires of antitank guided missiles, antitank artillery, other artillery and tanks conducting direct fire and by antitank grenade launchers and other means coordinated with antitank obstacles.

Antitank artillery of an army possess great capabilities in destroying enemy tanks. The numbers of antitank artillery in the army (composed of four motorized rifle divisions, one tank division, and one antitank brigade of the Supreme High Command reserve totals 594 pieces of antitank weapons.

In defense one antitank gun is considered capable of destroying two enemy tanks as a norm. Therefore, theoretically army antitank artillery is capable of destroying up to 1,200 enemy tanks. This constitutes the total tanks of four to five enemy divisions.

Employment of Antitank Reserves

Antitank reserves are established at all levels from the regiment to the front. Coverage capability in terms of fighting against tanks across the front is as follows:
platoon covers a 400 m front;
battery covers a 1,000 - 1,200 m front;
division's separate antitank battalion may cover a three to four kilometer front;
army's antitank regiment may cover a eight to nineteen kilometer front;
an antitank brigade of the Supreme High Command's reserve may cover a fifteen to twenty kilometer front.

The typical composition of antitank reserves at different levels is as follows:
division's separate antitank battalion constitutes the divisional antitank reserve;
army's antitank regiment constitutes the army's antitank reserve;
antitank brigade of the Supreme High Command reserve may constitute front antitank reserves.

When the army is reinforced by an antitank brigade of the Supreme High Command reserve, the army's antitank regiment will be employed to establish the antitank reserves of divisions operating on the main direction. In this case antitank brigades of the Supreme High Command reserve will be employed as the army's antitank reserve.

Missions of Front Antitank Reserves

Missions of front antitank reserves are as follows:
destroy enemy tanks which have penetrated into the defense;
reinforce army antitank defense;
repulse enemy strikes of large units of tanks;
cover flanks of second-echelon troops against tank attacks during the conduct of counterblows;
destroy enemy airborne troops;
cover opened and threatened flanks.

The number of front antitank reserves may reach one to two, which will jointly operate with mobile obstacle detachments (POZ).

Front antitank reserves deploy sixty to seventy kilometers from the forward line of defense on tank threatened directions. They establish two to three fire lines on each direction ten kilometers apart from one another.

Front antitank reserves along with antitank reserves of one army may cover thirty to thirty-one kilometers of front and may repel the attacks of up to two enemy divisions.

Combat Employment of Artillery in Front Counterblows During Defensive Operations

The front's counterblows during the defensive operation are a phase of change (a turning point) in the course of military actions. The front's counterblows may also be coordinated in a converging form against main enemy groupings which have penetrated the defense.

The maximum available forces and means are assigned for launching counterblows. This means that the required superiority of forces and means over the enemy on are established on actual directions.

During counterblows, efforts are made by artillery fires and strikes of air force and rockets to prevent the movement and arrival of enemy reserves and second-echelon forces to penetration areas. Here friendly forces launch their counterblows against enemy groupings which are kept in a blockade situation so that favorable conditions are created for their destruction in an isolated form.

Planning Counterblows

Planning of counterblows is conducted during the preparation of the operation. It is confirmed during the conduct of the operation. Based on decisions of the front commander, the front's artillery staff plans the following:
establish artillery groupings and time of their arrival in positions;
duration and structure of preparatory fire;
methods of support of counterblows by artillery;
troops control and signal communications.

Artillery Forces and Means Assigned to Support Counterblows

They include all artillery which is organic to the groupings of forces assigned to conduct counterblows such as, army's artillery groups, division's artillery groups, and regiment's artillery groups. These are established before or newly created as part of the regroupment to support the counterblows. Thus during the establishment of the groupings of forces for counterblows, regroupment of artillery may be made as well.

The following are also called to inflict losses on the confronting enemy and to support the forces which conduct the counterblows:
artillery groups of adjacent large units and army defending in the direction of the conduct of front counterblows;
front aviation and rocket troops.

In addition to the time of the movement of the artillery 1-1.5 hours of daylight for the artillery units and 2 hours of daylight for the army artillery is required for necessary preparation.

Prior to initiation of counterblows, an artillery preparatory fire is conducted. The duration depends on the desired level of enemy suppression or the distance to be covered by forces moving to launch counterblows, when it is to be conducted from the line of march. Generally speaking artillery preparatory fire in this case may last thirty to forty minutes. It may be conducted in two to three strikes each of ten to fifteen minutes. It may also be conducted in one heavy fire strike.

Artillery Missions During Preparatory Fire

Artillery missions during preparatory fire accomplish the following:
destroy enemy nuclear delivery means;
inflict effective losses on enemy artillery, mortars, antitank weapons, and air defense artillery;
suppress enemy personnel in close contact with forces which launch counterblows;
destroy enemy command and control systems.

Supporting Fire

Supporting fires for counterblows are conducted to the depth of enemy first-echelon battalions, i.e., up to three kilometers in the following ways:
successive concentration fire (PSO);
double successive concentration fire;
rolling barrage (OV);
massive fire (MO);
concentration fire (SO) on call, just as in the case of the assault supporting fire during the attack.

Accompanying Fire

Accompanying fire for counterblows is conducted by concentration fire (SO) and massive fire (MO) against targets which resist the counterattacking forces.

VII. Combat Employment of Rocket Troops in Front Offensive Operations

Role, Composition, Missions, and Principles of Combat Employment of Rocket Troops in Front Offensive Operations

The front offensive operation is part of the strategic operation in the TVD. It is conducted in coordination (interaction) with adjacent fronts and operational formations of other services of the armed forces. To achieve the aims of the offensive operation of the front, the decisive role is played by the actions of the strategic nuclear forces which destroy main enemy groupings and his vital targets and areas in the TVD. The most important role in this context is played by strategic rocket forces. Strategic rocket force's highly destructive power, accuracy of nuclear strikes, and their practically unlimited range of rocket strikes support the following:
infliction of decisive losses on enemy nuclear forces;
destruction of enemy military and economic potentials;
disruption of enemy government and military control systems at the strategic and operational levels;
infliction of losses on main enemy armed forces groupings in the TSMA.

During the initial nuclear strike the strategic rocket forces destroy the following targets in interaction with long-range aviation and naval nuclear forces in the TVD:
rocket and air force bases;
airfields of strategic and tactical aircraft (where nuclear armed aircraft are based);
positions of operational-tactical rockets;
important depots of nuclear ammunition;
air defense (PVO), antispace (PKO), and antiballistic missiles (PRO) forces and means;
large units of infantry in assembly areas (constituting the reserve of the important enemy groupings;
areas of mobilization of forces, naval bases, ports, administrative, political, and industrial centers, state and military command centers.

Despite this, there will be a large number of targets in the operational depth (up to 300 km) which are to be destroyed by front rocket troops such as the following: nuclear weapons;
air forces and nuclear depots;
main groupings of enemy forces, particularly tank and motorized forces;
command posts;
air defense means;
vital targets of enemy logistic echelons, the destruction of which will destroy the firmness and viability of the enemy in operational depths.

Since operational-tactical nuclear weapons have a longer range, higher accuracy, and different yields of nuclear rounds, they play a significant role in the quick destruction of important enemy tactical and operational targets.


Missions of Rocket Troops

The missions of rocket troops are as follows:
destroy enemy nuclear means such as, nuclear delivery means, nuclear aviation, and nuclear munitions depots;
destroy enemy main groupings of forces including, their tactical nuclear means, particularly enemy groupings of tanks and mechanized forces;
destroy enemy troop control and his command and control points such as, command posts, signal means, and enemy guidance (direction) centers;
destroy air defense means and systems such as, air defense rockets, air defense artillery, radar posts, and enemy fighter aviation;
inflict losses on enemy logistic targets and installations.


Main Principles of Employment of Rocket Troops

The main principles in employment of rocket troops are as follows:
nuclear weapons are used against well detected targets about which accurate reconnaissance information is acquired;
nuclear weapons are used in massive form by surprise to achieve the desired results from their use;
nuclear weapons are used to accomplish the most important tasks such as, destruction of nuclear weapons and main groupings of enemy forces;
nuclear weapons are used in close interaction with other services of the armed forces, service branches, and weapons.


Forms of the Conduct of Missions

Forms of the conduct of missions and strikes of rocket troops are as follows:
Massive Strikes: Such as, the front's initial nuclear strike;
Group Strikes: Employment of several nuclear rounds on one target such as, the use of two rounds on a battalion and the use of twelve to sixteen rounds on one division; Individual Strikes: Strikes on individual important targets.

Composition of front Rocket Troops

The composition of front rocket troops is not standard but depends on front missions and its role in strategic operations and types of operations (offensive or defensive). The composition of front rocket forces may include the following:

Front's Rocket Brigades: The number of such brigades in the front may be one to two. The brigade consists of the staff, three rocket battalions, control battery, transportation company, meteorological battery, combat engineer company, and several other separate subunits. Each rocket battalion has four launching systems and therefore, there are twelve launching pads (systems) in the brigade. If front rocket troops are composed of two rocket brigades, then there will be twenty-four launching pads (launchers) of R-300 operational-tactical rockets in the front. For each launcher there are two nuclear rounds (rockets) and therefore, in front rocket troops there may be twenty-four to forty-eight nuclear rounds.
Army's Rocket Brigade: As a rule there is one separate rocket brigade in each tank and combined arms army. Therefore, depending on the number of armies in front, there may be four to five army rocket brigades. The army's rocket brigade is composed of the following elements:
three rocket battalions;
control battery;
transportation company;
meteorological battery;
combat engineer company;
several other separate platoons.

Each rocket battalion had three launchers. Therefore, there are nine launchers (pads) of R-300 rockets in the army's rocket brigade. Each launcher has two nuclear rounds with a total of eighteen nuclear rounds (rockets) in the brigade.

Division's Separate Rocket Battalion: There is one separate rocket battalion in each motorized rifle and tank division. The division's separate rocket battalion is composed of two start batteries, control subunits, technical service platoon, and signal platoon. Each start battery includes two rocket launching pads. Therefore, there are a total of four launching pads (launchers) of R-65 rockets in the battalion. Each launching pad has three nuclear rounds with a total of twelve rounds in the battalion. When a front includes twenty-two to twenty-five motorized rifle and tank divisions there will be a total of eighty-eight to one-hundred launchers of tactical R-65 rockets with a total of 264-300 nuclear rounds of R-65 tactical rockets.

Tactical and Technical Characteristics of Rockets

The front and army rocket brigades, as a rule, are composed of R-300 operational-tactical rockets. Divisional rocket battalions are equipped with R-65 tactical rockets.

CHARACTERISTICS R-65 R-300
maximum range 67 km 300 km
minimum range 3.5 km 50 km
yield of nuclear rounds (kt) 3, 10, 20 20, 40, 100

Combat Capabilities of Rocket Troops

The combat capabilities of rocket troops in terms of inflicting losses on various targets, time to prepare for strikes, and their maneuverability are as follows:

Capabilities to Inflict Losses on Various Targets:

Front Rocket Troops: have the following capabilities for destroying or suppressing enemy targets:

During the initial nuclear strike the front rocket troops may destroy six to nine enemy divisions, as well as, the nuclear ammunition depots, command posts of corps, armies and army groups, significant warning, guidance, air and air defense control centers. They may also partially damage tactical aircraft on the airfields and may suppress the bulk of air defense rockets.

Army Rocket: Army rocket troops using nuclear warheads have the following capabilities:

They may destroy a Sergeant guided missile battalion and up to two to three enemy divisions, including their tactical nuclear delivery means. Or they may inflict 40% losses on 4-5 enemy divisions.
There are twenty-four to thirty-four operational-tactical (R-300) and tactical (R-65) rocket launching systems. The army may participate in front initial nuclear strikes with twenty-five launching systems. To destroy one division ten to twelve rockets are required. Six to eight rockets are needed to suppress one division.

Combat Capabilities of Division Rocket Troops: Combat capabilities of division's rocket troops are as follows:

Three to four divisional rockets with a yield of 3, 10, and 20 kilotons may destroy 3-4 targets such as, enemy command posts, two enemy tanks or infantry battalions at a depth of 50 km. The subsequent (repeated) strike may be launched after 1.5 hours.

Depth of destruction in terms of maximum range of rockets and distance of rockets positions from the forward line of friendly forces is as follows:

In the Attack:

Rocket brigade may destroy targets located up to a distance of 240-270 km from the frontline while the brigade deploys in positions 30-60 km behind the frontline. Divisional rocket battalions may destroy targets located up to a distance of fifty-five kilometers from the frontline. The battalions deploy in positions ten kilometers behind the frontline.

In Defense:

Rocket brigades may destroy targets located up to 220-240 km from the frontline. The brigade deploys in positions sixty to eighty kilometers behind the frontline.

Divisional rocket battalions may destroy targets located up to forty-five to fifty kilometers from the frontline. Battalions deploy in positions fifteen to twenty kilometers behind the frontline.

Capabilities to Prepare (to Get Ready) for Launching Strikes: The capability of rocket troops to prepare for strikes depends on the state of readiness of the rocket troops, their location, the occupation of positions and start positions by the rocket troops, charging (zapravka) of rockets, mounting of rockets on launchers (peregruzka), arming of the warhead (stikovka), direct fire preparation, and time to observe (reconfirm) targets to be destroyed. There are four degrees of technical readiness of rockets. Time required to launch from each degree of readiness is considered as follows:


DEGREE OF READINESS TIME TO LAUNCH

(R-65)

TIME TO LAUNCH

(R-300)

degree of readiness # 3 19 minutes 25 minutes
degree of readiness #2 16 minutes 19 minutes
degree of readiness #2a 5-7 minutes 13 minutes
degree of readiness #1 1 minute 4 minutes

Capability of Maneuver of Rocket Troops: The capability to manuever includes, assembling mountings of rockets, conduct of march (movement), and deployment of the rocket troops in positions. The accepted norms in this regard are shown in the following table.

TYPE OF SPEED TIME TIME SPEED TIME
ROCKET OF MOVE- TO TO DEPLOY OF OF MENT IN ASSEMBLY (IN MOVEMENT MOUNTING
KM/H (MINUTES) MINUTES) IN POSIITION MINUTES)
AREA

operational 30 30 to the 1km in 3 40 tactical degree min. rockets R-300 of readiness #3: 40 min.

to the
degree of readiness #2: 60 min.
tactical 30 20 to the - - rockets degree R-65 of readiness #3: 30 min. to the degree of read iness #2: 40 min.


Organization of Combat Employment of Rocket Troops in Front Offensive Operations

The organization of combat employment of rocket troops in front offensive operations includes a number of measures taken by the chief of artillery and rocket troops of the front and his staff. The important measures on organization of combat employment of rocket troops are as follows:
make decisions on employment of rocket troops;
plan combat employment of rocket troops;
assign missions to rocket troops;
prepare position areas of rockets and establish positions for the first-echelon divisions to support the covering of the deployment of main groupings of forces;
organize supply of nuclear and chemical rounds;
organize all types of supporting measures;
organize troop control, prepare the command posts, and establish signal systems;
maintain high combat-readiness of rocket troops for accomplishing assigned missions.

Planning Front Initial Nuclear Strike

The plan for the initial nuclear strike is an important part of the front's plan of operation. The missions of the initial nuclear strike are as follows:
destroy enemy nuclear weapons such as, enemy nuclear aviation, nuclear depots, and nuclear rockets;
destroy enemy groupings of forces, particularly enemy groupings of tanks and mechanized forces, including tactical nuclear means;
destroy enemy control systems such as, his command posts, signal centers, and guidance points;
destroy enemy air defense means;
inflict losses on enemy logistic targets and installations.

Planning of the initial nuclear strike is conducted by the front chief of staff, the chief of front operations directorate, in conjunction with the chief of front artillery and rocket troops, and the commander of the front air army. Plans are made on the basis of instructions from the front commander. The initial nuclear strike is included in the plan for combat employment of artillery and rocket troops and the graphic of the initial nuclear strike. The graphic of the initial nuclear strike reflects the time of arrival of rocket troops, time of deployment, technical preparation of fire (charging and mounting of rockets), and direct preparation for fire (simultaneously or successively bringing the troops to a state of readiness). As a rule rocket troops are brought to the degree of fire readiness number 1 fifteen minutes before fire to avoid enemy detection of our preparation for the initial nuclear strike.

The targets of the initial nuclear strike are generally specified by the front commander and the degree of losses to be inflicted on each target is also determined by the front commander. The graphic and structure of the initial nuclear strike are determined by the chief of front artillery and rocket troops and the commander of front air army through distribution of targets among rocket and aviation troops. The chief of front artillery and rocket troops then distributes the targets among rocket units and large units. In order to insure effective losses on targets, in some conditions the targets of divisional rockets are specified by the army's chief of artillery and rocket troops.

Parallel with the assignment of missions to subordinates by the front commander, the chief of front artillery and rocket troops determines the following:
fire positions and deployment of rocket troops there;
which large units (units) are to launch their strikes on which targets;
specific targets of fire and their ranges;
yield of nuclear rounds and number of rounds for each target;
center of each nuclear burst (explosion);
altitude of air bursts and security distance of friendly troops from the center of nuclear bursts.

During planning crisscrossing of the path of flight of rockets is avoided.
After the distribution of targets and nuclear rounds, the rocket troops move to their positions, occupy positions, and the rocket troops are brought to a state of full combat-readiness.

A large number of rocket launching systems (pads) are assigned to participate in the initial nuclear strike including, rockets of the second-echelon divisions of the first-echelon armies. To reinforce striking power, rockets with a high destructive power are assigned while tactical rockets fire two rockets. The first fire is conducted at the signal of the initiation of front initial nuclear strike, and the second fire is launched after the air force strikes.

The control of troops during the initial nuclear strike is conducted in accordance with the front signal. The chief of artillery and rocket troops of the front repeats the signal.

The initial nuclear strike is planned against targets located short of the boundary line of strategic nuclear strikes drawn at a distance of 250 km from the frontline and sometimes further on. The possibility of planning of enemy losses in the entire front operational depth is not excluded.


Organization of Front Initial Nuclear Strikes During the Conduct of the Offensive Operation

As a rule the initial nuclear strike of the front is planned in advance prior to the initiation of the operation. The missions are readjusted and confirmed in accordance with the actual combat situation during the conduct of the operation and assigned to subordinates. During direct preparation for fire the graphic of the initial nuclear strike is updated and necessary changes are incorporated in the graphics. The specifics on the preparation of front initial nuclear strikes during the conduct of the operation are as follows.

Reconnaissance becomes very important, and information about targets to be destroyed is continuously acquired and reconfirmed. Accordingly, planning of nuclear strikes is adjusted. More responsibility is delegated to the army and division commanders with targets selected by them. All rocket troops and means of control are maintained at the highest level of combat-readiness. Missions are conveyed quickly to the troops. Continuous control of the fulfillment of missions is conducted.

The rocket troops are timely and regularly moved during the conduct of the operation. The level of combat-readiness of rocket troops to use nuclear weapons is upgraded during the course of the operation.

The timely and thorough organization of technical support of rockets is conducted and timely relocation of rocket troop positions are effected. The all-around combat supporting measures of rocket troops are taken such as, the preparation of position areas, engineer support, concealment (maskirovka) of the combat formation of the rocket troops, protection against mass-destruction weapons, providing close security, and defense measures.

As the time of the initiation of the initial nuclear strike nears, the start batteries are brought to a high state of combat-readiness and technical preparation of rockets for fire is conducted. The signal to bring the rocket troops to required levels of readiness is given by the front commander.

The control of the rocket troops in this phase is fully exercised in a centralized form by the army commanders.


Employment of Front Rocket Troops to Repel Enemy Counterblows

In order for the enemy to stop the attack of the friendly troops he will launch counterblows (counterstrikes) using his reserves. This will prevent further advance into the depth of his territory and subsequently destroy the attacking forces. If enemy counterblows succeed in stopping the attack of friendly troops and destroying them, then the enemy may open a new phase in the course of the conduct of the front offensive operation.

To foil enemy counterblows (counterstrikes) rocket troops are employed in the following ways:
continuous and reconfirming reconnaissance of enemy nuclear weapons, detection of their preparation for fire, and location of enemy reserve assembly areas, and directions of their movement;
maintaining rocket troops in the highest state of combat-readiness so that they may quickly launch their decisive strikes on the enemy;
launching massive and group nuclear strikes on enemy reserves in assembly areas, during their movement, and during their deployment to launch their counterblows (counterstrikes) on friendly forces;
if the enemy succeeds in deploying, then massive nuclear strikes are launched on his main tank and mechanized forces, his command posts and artillery;
then strikes of friendly tank and motorized rifle troops are launched against the flanks and rear of main enemy groupings which are conducting the counterblow, the grouping is encircled and destroyed while the main forces continue advancing into the depth of enemy defenses.


Organization of Combat Supporting Measures of the Front Rocket Troops

The combat supporting measures of rocket troops constitute one of the main factors in achieving success in combat. The combat supporting measures are taken for the following reasons:
to create favorable conditions for friendly fires;
to reduce the effectiveness of enemy nuclear and conventional fire and actions of enemy troops;
to destroy the enemy's troop control system.

Combat supporting measures include the following:
acquisition of reconnaissance and reconfirming reconnaissance information on enemy targets;
preparation of position areas;
concealment of (maskirovka of) position, engineer installations of the terrain, weapons and combat equipment;
protection of troops against enemy mass-destruction weapons;
close security;
defense against enemy air strikes;
radio-electronic combat;
rocket supporting measures;
topogeodetic, topographic, and hydrometeorological support;
rear service, material, and medical support.

Combat-Readiness of Rocket Troops

There are three levels of combat-readiness specified for rocket troops:

1. Constant Combat-Readiness of Rocket Troops: Personnel conduct their routine training in accordance with designated plans and are capable of conducting assigned missions. Equipment is ready for combat employment. Armament, ammunition, and material means are supplied up to the norms.

2. Higher Combat-Readiness: This is a state of combat-readiness from which the units and subunits may be brought to full combat-readiness in the shortest time. In this state of combat-readiness all units and subunits are brought back to the garrison from exercise areas and other off-post duties. They are put on a full on-post accommodation. Combat duty detail is reinforced and combat service is conducted in full combat-readiness. Officers and men are called back from leave status. Ammunition, material means, and other supplies and equipment are loaded on vehicles. Units and subunits are ready to move out from the garrison. Operational groups with signal communication means are detached to command posts. Two to three hours are required to bring the rocket troops to the state of higher readiness.

3. Full Combat-Readiness: This is assumed in accordance with the plan or on combat alert signals. Under this state of combat-readiness the units and subunits move out of their garrisons to assembly areas and position areas. They then occupy fire positions. Units and subunits conduct technical readiness, launching pads (systems) are loaded, and units get prepared for the conduct of missions. Units and subunits in assembly areas are augmented up to full combat strength on the account. of the mobilization reserves.

The time needed to achieve full combat-readiness in 6.5-7 hours for the rocket brigades excluding the time required to cover the necessary distance.

Full combat-readiness is a state in which rocket troops and artillery may rapidly initiate the conduct of combat missions, i.e., armies and front rocket brigades and rocket battalions of motorized rifle and tank divisions deploy in their position areas and they are ready to initiate actions planned in the front's initial nuclear strike. In full combat-readiness start batteries are in main or start positions in the state of readiness number 3, 2, 2A, or 1.


Technical Preparation of Rockets

When the signal is received rocket troops take the following measures.

Rocket troops occupy main position areas or they deploy in assembly areas designated to be occupied after receiving the combat alert signal. There, rocket troops conduct technical preparations for fire. Four sites of assembling and charging (fueling) of rockets are established in a rocket brigade (one at the technical base of rockets and one each in technical platoons of rocket battalions, which totals four). At this point charging (fueling), loading, and mounting of warheads begins. The time of charging (fueling), loading, and mounting of the warhead is as follows:

TYPE OF ACTION R-65 TACTICAL ROCKET R-300 TACTICAL/ OPERATIONAL ROCKET
fueling-charging (zapravka) - 60 min.
loading (peregruzka) 15 min. 40 min.
mounting (stikovka( 25 min. 60 min.

Then launchers (launching pad) is moved to the start (main position. There, depending on the situation, they are placed in state of readiness number 3, 2, 2A, or 1.

Technical readiness is as follows:

Readiness Number 3: The start battery is deployed in the start position. Launchers are loaded and the battery may fire after twenty-five minutes.

Readiness Number 2: The start battery is directed (aimed) at the main (osnovnoi) direction, the rocket is in a horizontal position. Fire may be launched after nineteen minutes.

Readiness Number 2A: The rocket is aimed at the target. The securing mechanism is released from the rocket. Fire may be launched after thirteen minutes.

Readiness Number 1: The rocket is aimed at the target and is brought into a vertical position. Three to four minutes are required to launch the rocket.

Time for Bringing Rocket Troops to Full Combat-Readiness

1. To bring R-300 rocket brigades to state of readiness number 3, when four sites of assembling and charging (fueling) of rockets are established, 6.5-7 hours are required (excluding the march and movement time). This time may be broken down as follows:
time to assemble on combat alert signal (thirty-forty minutes);
time to deploy rocket technical subunits (twenty minutes);
total time of technical preparation (five hours).

To bring divisional R-65 rocket battalions to readiness number 3, when two sites of assembling and loading of rockets are established, a two hour time is required (excluding the march and movement time). This time may be broken down as follows:
time to assemble on combat alert signal (thirty to forty minutes);
time to deploy rocket technical subunits (five minutes);
total time of technical preparation in divisional separate rocket battalion (eighty minutes).

Other calculations related to movement and deployment of rocket troops are as follows:
speed of advance of rocket troops during the march (twenty-five to thirty kilometers per hour);
time for deployment of a separate rocket battalion (divisional) (forty minutes);
time for deployment of a rocket brigade (2.5 hours);
time to reassemble:
for battalion (forty minutes;
for brigade (2.5 hours).